iei 2000em keypad programming instructions

IEI 2000EM KEYPAD PROGRAMMING INSTRUCTIONS FOR FREE
IEI 2000EM KEYPAD PROGRAMMING INSTRUCTIONS DRIVER
IEI 2000EM KEYPAD PROGRAMMING INSTRUCTIONS MANUAL
IEI 2000EM KEYPAD PROGRAMMING INSTRUCTIONS CODE

Personal entry code positions you wish to use. Press 1-2, 3-4 or 5-6 to indicate which of the three Each number must beĮntered within five seconds of each other. Within five seconds press the 1-2 on the keypad. Up to three personal entry codes may be programmed to the vehicle. Press the middle of the controls to ensure a good activation. When pressing the controls on the keypad, The factory set code cannot be reprogrammed but you can create your ownĥ digit personal entry code.

To program the third code, press the reset button 3 time, then enter your 4-8.

To program the second code, press the reset button twice, then enter your 4-8.

To program the first code, press the reset button once, then enter your 4-8ĭigit code on the exterior keypad, then immediately press the middle.

I determinate that I put the third code by error the was i program it the firs time. Have just to press the program button 3 time for the third code. You can put the same code in each third emplacement. and the problem you have is the thirdĬode not reset. Is not a 2 codesĭoor lock, it's a 3 codes one. IĬonclude that this dorr lock is better that is appear. Your personal code is now erased and only the factory set 5-digit codeįirst, I fix this problem after an hour of try. Programmed code this must be done within five seconds of completing

2 for two seconds to erase the customer.

2 for two seconds and release this must beĭone within five seconds of completing step 1.

If you set a personal code and store it over an existing personal code.

The factory set code will work even if you have set your own personal.

Do not use five numbers in sequential order.

Do not set a code that uses five of the same number.

Wait 5 seconds without pressing a keypad button in order to store a personal entry code.

IEI 2000EM KEYPAD PROGRAMMING INSTRUCTIONS DRIVER

0 does not recall a driver personality.

Note: The lock motors will cycle, locked then unlocked. Enter a sixth digit to indicate which personality feature should be recalled by the personal code.

Each number must be entered within five seconds of each other. Note: The lock motors will cycle, locked then unlocked 3. To create your own personal entry code: 1. When pressing the controls on the keypad, press the middle of the controls to ensure a good activation. You can also create your own 5-digit personal entry code. The keypad can be operated with the factory set 5-digit entry code this code is located on the owner's wallet card in the glove box, is marked on the computer module, and is available from your authorized dealer. recall memory seat/mirrors/steering column/adjustable pedals positions1 or 2.lock or unlock the doors without using a key.if not to the dealership is where you will have to go

IEI 2000EM KEYPAD PROGRAMMING INSTRUCTIONS MANUAL

The code cn usually be found in the owners manual on a card.

IEI 2000EM KEYPAD PROGRAMMING INSTRUCTIONS FOR FREE

If you dont have the original code you will have to find a factory scanner to retrieve the code some places will do this for free others charge. The doors will lock then unlock to confirm programming of the newģ. Note: The keypad and the interior lampsģ. You have to have the factory code to progam a new code in one code is perminantly programed the sedond code can be entered after the original code is put in. Once the program CODE has been saved the programming mode is excited by pressing any key.if the new code is incorrect this process should be repeated.the programming mode can be excited at any time by pressing door alarm key for 3 seconds or will exit if unattended for 4 minutes.good luck but will beep ,(the unit will not run with a program code of 0000 ,). Once the desired program code is entered press & hold the freezer temperature down keypad until the program CODE begins flashing indicating it has been u attempt to enter an invalid code the control will not save the new code. the decimal point indicates the selected digit press the freezer temperature Up keypad to select next digit. NOTE.IF THE PROGRAM code is correct the programming mode is excited by pressing door alarm keypad for 3 seconds.7.press the refrigerator temperature up keypad or refrigerator down keypad to change the digit value with each key press.

4.the control will DISPLAY PE to indicate the programming mode 5.entry is confirmed by pressing the freezer temperature down keypad once more.6 the control will display the current program CODE this program should be validated with the program CODE printed on the unit serieal plate. 1 press & hold the door alarm keypad.2 press & hold freezer temperature down keyboard within 3 seconds.3 release the door alarm alarm keypad and wait 3 seconds.

Iei 2000em keypad programming instructions